ceiling air conditioner

Window and through-wall units
Room air conditioners come in two forms: unitary and packaged terminal PTAC systems. Unitary systems, the common one room air conditioners, sit in a window or wall opening, with interior controls. Interior air is cooled as a fan blows it over the evaporator. On the exterior the air is heated as a second fan blows it over the condenser. In this process, heat is drawn from the room and discharged to the environment. A large house or building may have several such units, permitting each room be cooled separately. PTAC systems are also known as wall split air conditioning systems or ductless systems. These PTAC systems which are frequently used in hotels have two separate units (terminal packages), the evaportive unit on the exterior and the condensing unit on the interior, with tubing passing through the wall and connecting them. This minimizes the interior system footprint and allows each room to be adjusted independently. PTAC systems may be adapted to provide heating in cold weather, either directly by using an electric strip, gas or other heater, or by reversing the refrigerant flow to heat the interior and draw heat from the exterior air, converting the air conditioner into a heat pump. While room air conditioning provides maximum flexibility, when cooling many rooms it is generally more expensive than central air conditioning.

Evaporative coolers
In very dry climates, evaporative coolers are popular for improving comfort during hot weather. This type of cooler is the dominant cooler used in Iran, which has the largest number of these units of any country in the world, causing some to referring to these units as "Persian coolers."  An evaporative cooler is a device that draws outside air through a wet pad, such as a large sponge soaked with water. The sensible heat of the incoming air, as measured by a dry bulb thermometer, is reduced. The total heat (sensible heat plus latent heat) of the entering air is unchanged. Some of the sensible heat of the entering air is converted to latent heat by the evaporation of water in the wet cooler pads. If the entering air is dry enough, the results can be quite comfortable; evaporative coolers tend to feel as if they are not working during times of high humidity, when there is not much dry air with which the coolers can work to make the air as cool as possible for dwelling occupants. Unlike air conditioners , evaporative coolers rely on the outside air to be channeled through cooler pads that cool the air before it reaches the inside of a house through its air duct system; this cooled outside air must be allowed to push the warmer air within the house out through an exhaust opening such as a open door or window.

These coolers cost less and are mechanically simple to understand and maintain.
An early type of cooler, using ice for a further effect, was patented by John Gorrie of Apalachicola, Florida in 1842. He used the device to cool the patients in his malaria hospital.

Portable air conditioners
Portable air conditioners (or PACs) are moveable units that can be used to cool a specific room in a home and do not require permanent installation. Warm air in the room is drawn in through inlets on the portable air conditioner. The air is circulated through the unit and is cooled by evaporator coils with refrigerant running through them and then blown out through the front. Remaining hot air in the unit is expelled and vented through the back with an exhaust hose. All portable air conditioners require exhaust hoses for venting.

Single Hosed Units
A single hosed unit has one hose that runs from the back of the portable air conditioner to the vent kit where hot air can be released. A single hosed portable air conditioner can cool a room that is 475 sq. ft. or smaller and has at most a cooling power of 12,000 BTUs.

Dual Hosed Units
Dual hosed units are typically used in larger rooms. One hose is used as the exhaust hose to vent hot air and the other as the intake hose to draw in additional air (usually from the outside). These units generally have a cooler power of 12,000-14,000 BTUs and cool rooms that are around 500 sq. ft. The reason an intake hose is needed to draw in extra air is because with higher BTU units, air is cycled in large amounts and hot air is expelled at a faster rate. This creates negative air pressure in the room, and the intake hose stabilizes the room's air pressure.

Split Units
Portable units are also available in split configuration, with the compressor and evaporator located in a separate external package and the two units connected via two detachable refrigerant pipes, as is the case with fixed split systems. Split portable units are superior to both single and dual hosed mono-portable units in that interior noise and size of the internal unit is greatly reduced due to the external location of the compressor, and no water needs to be drained from the internal unit due to the exterior location of the evaporator.

A drawback of split portable units compared with mono-portables is that a surface exterior to the building, such as a balcony must be provided for the external compressor unit to be located.

Unlike window ACs the split AC does not have an option of exchange of indoor and outdoor air.

Heat and Cool Units
Some portable air conditioner units are also able to provide heat by reversing the cooling process so that cool air is collected from a room and warm air is released. These units are not meant to replace actual heaters though and should not be used to cool rooms lower than 50 °F (10 °C).

Central air conditioning
Central air conditioning, commonly referred to as central air (U.S.) or air-con (UK), is an air conditioning system which uses ducts to distribute cooled and/or dehumidified air to more than one room, or uses pipes to distribute chilled water to heat exchangers in more than one room, and which is not plugged into a standard electrical outlet.

With a typical split system, the condenser and compressor are located in an outdoor unit; the evaporator is mounted in the air handler unit. With a package system, all components are located in a single outdoor unit that may be located on the ground or roof.

Central air conditioning performs like a regular air conditioner but has several added benefits:

    * When the air handling unit turns on, room air is drawn in from various parts of the building through return-air ducts. This air is pulled through a filter where airborne particles such as dust and lint are removed. Sophisticated filters may remove microscopic pollutants as well. The filtered air is routed to air supply ductwork that carries it back to rooms. Whenever the air conditioner is running, this cycle repeats continually.

    * Because the condenser unit (with its fan and the compressor) is located outside the home, it offers a lower level of indoor noise than a free-standing heat pums unit.

Mini (Small) Duct, High Velocity
A central air conditioning system using high velocity air forced through small ducts (also called mini-ducts), typically round, flexible hoses about 2 inches in diameter. Using the principle of aspiration, the higher velocity air mixes more effectively with the room air, eliminating temperature discrepancies and drafts. A high velocity system can be louder than a conventional system if sound attenuators are not used, though they come standard on most, if not all, systems.

The smaller, flexible tubing used for a mini-duct system allows it to be more easily installed in historic buildings, and structures with solid walls, such as log homes. These small ducts are also typically longer contiguous pieces, and therefore less prone to leakage. Another added benefit of this type of ducting is the prevention of foreign particle buildup within the ducts, due to a combination of the higher velocity air, as well as the lack of hard corners.

from:wiki

An air conditioner is a home appliance, system, or mechanism designed to dehumidify and extract heat from an area. The cooling is done using a simple refrigeration cycle. In construction, a complete system of heating, ventilation, and air conditioning is referred to as "HVAC." Its purpose, in a building or an automobile, is to provide comfort during either hot or cold weather.

In 1758, Benjamin Franklin and John Hadley, professor of chemistry at Cambridge University, conducted an experiment to explore the principle of evaporation as a means to rapidly cool an object. Franklin and Hadley confirmed that evaporation of highly volatile liquids such as alcohol and ether, could be used to drive down the temperature of an object past the freezing point of water. They conducted their experiment with the bulb of a mercury thermometer as their object and with a bellows used to "quicken" the evaporation; they lowered the temperature of the thermometer bulb down to 7 °F (−14 °C) while the ambient temperature was 65 °F (18 °C). Franklin noted that soon after they passed the freezing point of water (32°F) a thin film of ice formed on the surface of the thermometer's bulb and that the ice mass was about a quarter inch thick when they stopped the experiment upon reaching 7 °F (−14 °C). Franklin concluded, "From this experiment, one may see the possibility of freezing a man to death on a warm summer's day".

In 1820, British scientist and inventor Michael Faraday discovered that compressing and liquefying ammonia could chill air when the liquefied ammonia was allowed to evaporate. In 1842, Florida physician John Gorrie used compressor technology to create ice, which he used to cool air for his patients in his hospital in Apalachicola, Florida. He hoped eventually to use his ice-making machine to regulate the temperature of buildings. He even envisioned centralized air conditioning that could cool entire cities. Though his prototype leaked and performed irregularly, Gorrie was granted a patent in 1851 for his ice-making machine. His hopes for its success vanished soon afterward when his chief financial backer died; Gorrie did not get the money he needed to develop the machine. According to his biographer Vivian M. Sherlock, he blamed the "Ice King", Frederic Tudor, for his failure, suspecting that Tudor had launched a smear campaign against his invention. Dr. Gorrie died impoverished in 1855 and the idea of air conditioning faded away for 50 years.

Early commercial applications of air conditioning were manufactured to cool air for industrial processing rather than personal comfort. In 1902 the first modern electrical air conditioning was invented by Willis Haviland Carrier in Syracuse, NY. Designed to improve manufacturing process control in a printing plant, his invention controlled not only temperature but also humidity. The low heat and humidity were to help maintain consistent paper dimensions and ink alignment. Later Carrier's technology was applied to increase productivity in the workplace, and The Carrier Air Conditioning Company of America was formed to meet rising demand. Over time air conditioning came to be used to improve comfort in homes and automobiles. Residential sales expanded dramatically in the 1950s.

In 1906, Stuart W. Cramer of Charlotte, North Carolina, was exploring ways to add moisture to the air in his textile mill. Cramer coined the term "air conditioning", using it in a patent claim he filed that year as an analogue to "water conditioning", then a well-known process for making textiles easier to process. He combined moisture with ventilation to "condition" and change the air in the factories, controlling the humidity so necessary in textile plants. Willis Carrier adopted the term and incorporated it into the name of his company. This evaporation of water in air, to provide a cooling effect, is now known as evaporative cooling.

The first Heat pump and refrigerators employed toxic or flammable gases like ammonia, methyl chloride, and propane which could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first chlorofluorocarbon gas, Freon, in 1928. The refrigerant was much safer for humans but was later found to be harmful to the atmosphere's ozone layer. Freon is a trademark name of DuPont for any chlorofluorocarbon (CFC), hydrogenated CFC (HCFC), or hydrofluorocarbon (HFC) refrigerant, the name of each including a number indicating molecular composition (R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as R-22. It is to be phased out for use in new equipment by 2010 and completely discontinued by 2020. R-12 was the most common blend used in automobiles in the United States until 1994 when most changed to R-134A. R-11 and R-12 are no longer manufactured in the United States, the only source for purchase being the cleaned and purified gas recovered from other air conditioner systems. Several non-ozone depleting refrigerants have been developed as alternatives, including R-410A, known by the brand name Puron. The most common ozone-depleting refrigerants are R-22, R-11, and R-123.

Innovation in air conditioning technologies continue, with much recent emphasis placed on energy efficiency and improving indoor air quality. As an alternative to conventional refrigerants, natural alternatives like CO2 (R-744) have been proposed.

from:wiki