http://www1.shhqzx.cn/blog/member.asp?action=view&memName=RustyMatheny461736 - ikea kitchen installation service in Florida -
Kitchen Cupboard Installation - Step-By-Step Guidance regarding how to Put in Kitchen Cabinets Your self
Now that you might have your new kitchen area cabinets, you're completely ready to move on into the next huge stage.....Setting up your kitchen area cabinets. While the actual installation of the Kitchen Cupboards isn'tall that arduous, the critical to start with phase is measuring and marking out exactly where the cupboards will go. By putting layout markings to the walls and floors, it will eventually not only help you with kitchen cabinet placement and stud destinations, nonetheless it will also help you identify in which changes and shims is going to be expected. Right before we begin there are actually a couple of things that you will want for that project:
Stage or Laser Level
1" x 3" Bit of lumber (6'-8' in size) or an Inverted U-shaped frame (see notes beneath)
Screws (extensive plenty of to go 1 1/2 into your studs)
Utility knife or chisel
An additional set of hands (chances are you'll have to bribe 1 within your mates)
As I discussed higher than, you've got the option of employing a piece of 1' x 3' lumber for your set up or developing a frame to help the cupboards (I've provided a picture of a sample frame underneath). This may be made from 2' x 4's and will be tall enough to guidance the bottom of the wall cupboards. In the event you prepare on installing more than one kitchen area, then I'd personally counsel the body, but a piece of lumber will just do fine if that is a one particular time party. In possibly case, you can need to have a different set of arms that can help with the set up.
In such cases we purchased (RTA) Ready-To-Assemble Kitchen area Cabinets from RTA Kitchen & Bathroom Cabinet Store. Now the kitchen cabinets are assembled, we are completely ready to start marking out our format lines. Some people start with all the base cabinets, but we are going to start together with the wall cabinets very first. There is no right or wrong way to start, I just prefer to start along with the upper cabinets very first.
1. Use a amount and a pencil to draw a parallel line across the wall about 3 inches up from the floor. Measure down from this line, into the floor, and find the floors high point (if it has just one), and mark a line at that point. From that high point, Evaluate up 34 1/2 inches and draw a stage line across the wall to designate the top with the base cabinets.
two. Since you have the top from the base cabinets marked, evaluate up yet another 19 1/2 inches and a stage line across the wall to indicate the underside on the wall cabinets. Lightly mark each cabinets' dimensions and placement within the wall to make sure that your original layout is correct.
three. Use a stud finder to locate the wall studs. Use a pencil to mark the stud areas at least 6 inches above and down below the line for that base from the wall cupboards. Draw straight vertical lines between the top and base marks to indicate the center in the studs.
4. In case you decided to go using the piece of 1' x 3' lumber, now is exactly where you can use (if you decided to go along with the U-shaped body, it's going to come into play after all your lines are laid out). Screw a temporary 1' x 3' aid rail into the wall, aligning the top edge with the rail with all the line for your bottom edge from the wall cupboards. Attach it by driving three or 4 two inch screws through the rail in the wall studs.
5. Given that we have all the lines marked, it is time to start putting in your kitchen area cupboards. We are going to start along with the corner cupboard (here is exactly where your helper's additional established of arms will probably be needed). Place the corner cabinet onto the temporary assist rail and have your helper hold the corner cupboard in place. Drill pilot holes through the sturdy cupboard back or its guidance rail and to the wall studs. Screw the cupboard to the wall using two screws that are long adequate to penetrate the studs by at least 1 1/2 inches. Check the top with the cupboard for level and the front of the cabinet for plumb. If you should correct the position, just back the screws out a little bit and top shims behind the cupboard at the stud locations. If it is plumb and degree, drive the screws all the way in and add several far more into each stud to ensure that the cupboard is secured tightly to the wall.
6. Now we are going to move onto the cupboards on both side of the corner cupboard. As you set up each a single, use the clamps to secure each cabinet towards the neighboring cabinet and then check it for plumb with your level. On faceframe cupboards, it can be a good idea to drill two 1/8 inch pilot holes through the sides with the faceframe and use screws. In such a case, with frameless, ready-to-assemble kitchen area cabinets we are going to screw through the plywood sides and use shims in between the cupboards to ensure a tight fit and make sure that the cupboard faces are plumb.
7. After all the wall cupboards are in place, install the corner or end base scenario cabinet. Use shims exactly where needed to degree the cupboard and raise it up towards the line which indicates the high point with the floor. Be sure it is degree from front to back and from side to side, then screw it into the wall studs. When you don't have a diagonal corner cabinet or blind base cupboard in the corner, push the adjoining cabinet into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers adequate clearance to open and close properly. If necessary, tap shims under the cupboard and behind it to adjust for plumb and amount.
8. Drive screws through the cupboard back (and shims) into the wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cabinets during this manner, joining them the same way you connected the wall cabinets in action 6.
9. If your cupboards end up butting against another wall, you could possibly require a filler strip to make up the last few inches. In the event you have custom cupboards, they really should have been built to fill this gap, but in the event you are employing stock or RTA Kitchen Cabinets the filler strip may perhaps be needed. For those who do need to use a filler strip, leave the last cabinet detached from the other cupboards. Clamp a straightedge for the face of the nearest installed unit, extending far adequate for you to put alignment marks over the end wall. Allow a 3/4" offset behind those marks (with the thickness on the filler piece) and fasten a cleat for the wall. Then set up and fasten the last cabinet and measure the gap between its face body and the wall.
If the wall is flat, simply rip the filler board for the required width and fasten it in place. If the wall is irregular, you'll really have to scribe-fit the filler board. Start by setting a marking compass to the width with the gap, then place a strip of 1"-wide masking tape along the filler board in the area where it needs to be trimmed. Clamp the board to your end cabinet's face body, then trace the wall contour using the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face frame in the edge on the filler board. Screw or nail the other side into the cleat.
At this point, your kitchen cupboard set up is complete. If you purchased matching crown molding or any other details, these need to be easily installed now. Depending on whether you had to use shims under the base cupboards, chances are you'll need to put in some trim pieces by the toe kicks to cover up the shims or any gaps at the bottom from the kitchen area cupboards.
I hope this helps make your kitchen area cabinet set up as smooth as possible. For those who have to have any help with cabinet selection, kitchen area format tips, or ideas for cupboard styles, check out RTA Kitchen area & Bathroom Cabinet Store.