http://www.wanghxiu.com/comment/html/index.php?page=1&id=30430 - ikea assembly -
Kitchen area Cabinet Installation - Step-By-Step Guidance regarding how to Install Kitchen Cupboards Yourself
Given that you've your new kitchen cabinets, you are ready to move on for the upcoming huge move.....Installing your kitchen area cupboards. Whilst the particular set up from the Kitchen area Cupboards isn'tall that tough, the critical 1st stage is measuring and marking out exactly where the cabinets will go. By placing format markings to the partitions and flooring, it can not only help you with kitchen cabinet placement and stud locations, however it may even assist you identify in which adjustments and shims will probably be needed. Prior to we start out there are a few of things that you will need for that challenge:
Stage or Laser Level
1" x 3" Piece of lumber (6'-8' in length) or an Inverted U-shaped body (see notes down below)
Screws (long sufficient to go one 1/2 in to the studs)
Utility knife or chisel
An extra established of fingers (you could have to bribe one of one's good friends)
As I mentioned over, you have the choice of utilizing a piece of 1' x 3' lumber with the installation or developing a body to aid the cupboards (I've included an image of the sample frame under). This may be made out of 2' x 4's and may be tall enough to guidance the underside of your respective wall cabinets. Should you system on installing multiple kitchen area, then I might counsel the body, but a bit of lumber will do exactly high-quality if this can be a a single time function. In either situation, you will will need yet another established of fingers that can help using the set up.
In this instance we bought (RTA) Ready-To-Assemble Kitchen area Cupboards from RTA Kitchen & Bathroom Cupboard Store. Now the kitchen cabinets are assembled, we are all set to start marking out our layout lines. Some people start while using the base cabinets, but we are going to start along with the wall cupboards to start with. There is no right or wrong way to start, I just prefer to start with the upper cabinets 1st.
1. Use a stage and a pencil to draw a parallel line across the wall about 3 inches up from the floor. Evaluate down from this line, to the floor, and find the floors high point (if it has a single), and mark a line at that point. From that high point, Measure up 34 1/2 inches and draw a level line across the wall to designate the top with the base cabinets.
2. Given that you've got the top in the base cupboards marked, measure up yet another 19 1/2 inches and a degree line across the wall to indicate the underside with the wall cupboards. Lightly mark each cabinets' dimensions and placement to the wall to make sure that your original structure is correct.
3. Use a stud finder to track down the wall studs. Use a pencil to mark the stud areas at least 6 inches above and underneath the line for that base from the wall cabinets. Draw straight vertical lines between the top and base marks to indicate the center with the studs.
4. In the event you decided to go using the piece of 1' x 3' lumber, now is wherever you'll use (for those who decided to go while using the U-shaped body, it is going to come into play after all your lines are laid out). Screw a temporary 1' x 3' help rail to the wall, aligning the top edge from the rail while using the line to the base edge in the wall cabinets. Attach it by driving three or 4 two inch screws through the rail into the wall studs.
5. Now that we have all the lines marked, it is time to start setting up your kitchen area cupboards. We are going to start while using the corner cupboard (here is where your helper's more established of fingers is going to be needed). Place the corner cabinet onto the temporary guidance rail and have your helper hold the corner cupboard in place. Drill pilot holes through the sturdy cupboard back or its help rail and into the wall studs. Screw the cupboard to the wall working with two screws that are lengthy plenty of to penetrate the studs by at least one 1/2 inches. Check the top in the cupboard for degree and the front of the cabinet for plumb. In case you should correct the position, just back the screws out a little bit and top shims behind the cabinet at the stud spots. If it is plumb and stage, drive the screws all the way in and add several more into each stud to ensure that the cabinet is secured tightly for the wall.
6. Now we are going to maneuver onto the cabinets on either side from the corner cupboard. As you put in each just one, use the clamps to secure each cabinet on the neighboring cabinet and then check it for plumb with your amount. On faceframe cupboards, it is usually a good idea to drill two 1/8 inch pilot holes through the sides in the faceframe and use screws. In this instance, with frameless, ready-to-assemble kitchen cabinets we are going to screw through the plywood sides and use shims in between the cabinets to ensure a tight fit and make sure that the cupboard faces are plumb.
7. After all the wall cupboards are in place, set up the corner or end base scenario cupboard. Use shims where by needed to degree the cabinet and raise it up on the line which indicates the high point of your floor. Be sure it is degree from front to back and from side to side, then screw it to your wall studs. In the event you don't have a diagonal corner cupboard or blind base cupboard in the corner, push the adjoining cabinet into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers enough clearance to open and close properly. If necessary, tap shims under the cupboard and behind it to adjust for plumb and level.
8. Drive screws through the cupboard back (and shims) into the wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cupboards in this manner, joining them the same way you connected the wall cabinets in stage 6.
9. If your cabinets end up butting against yet another wall, you could possibly require a filler strip to make up the last few inches. In case you have custom cupboards, they really should have been built to fill this gap, but in case you are using stock or RTA Kitchen Cabinets the filler strip may perhaps be needed. When you do will need to use a filler strip, leave the last cupboard detached from the other cupboards. Clamp a straightedge into the face from the nearest installed unit, extending far more than enough for you to put alignment marks to the end wall. Allow a 3/4" offset behind those marks (for the thickness from the filler piece) and fasten a cleat into the wall. Then put in and fasten the last cabinet and evaluate the gap between its face frame and the wall.
If the wall is flat, simply rip the filler board to the expected width and fasten it in place. If the wall is irregular, you'll need to scribe-fit the filler board. Start by setting a marking compass for the width of your gap, then place a strip of 1"-wide masking tape along the filler board in the area the place it needs to be trimmed. Clamp the board to the end cabinet's face frame, then trace the wall contour using the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face body into your edge of your filler board. Screw or nail the other side to your cleat.
At this point, your kitchen cabinet set up is complete. If you purchased matching crown molding or any other details, these should be easily installed now. Depending on whether you had to use shims under the base cabinets, you could possibly have to set up some trim pieces by the toe kicks to cover up the shims or any gaps at the underside of your kitchen area cupboards.
I hope this helps make your kitchen area cabinet installation as smooth as possible. Should you need to have any help with cabinet selection, kitchen area structure tips, or ideas for cabinet styles, check out RTA Kitchen & Bathroom Cupboard Store.